Vendor R/W series flywheel's

[SuperRunner]

I have a few flywheels ready to be shipped out. I currently have 3 in stock and can be shipped out immedatly. These flywheels can be used both in R series and W series transmissions. You just have to select which holes to put the alignment pin in.

These flywheels are $250 + shipping, but only while these 3 last. There was a mistake at the machine shop and they drilled more than I requested. After these 3, they will be $300 + shipping for the dual R/W flywheels.

If you want one for a W series only, the cost is $235+ shipping. I had to increase the price from $200 due to an increased cost in machine work.

Please do not PM me as my storage is almost filled up. Send me an e-mail at [email protected] or send paypal funds to [email protected]. If paypal, please include 3%.

Thanks
-Rob

 

[SuperRunner]

You can PM me now, I have space.

Thanks Lextreme!

 

[SuperRunner]

Cast steel, about 23 lbs, and the ring gear is on the right direction. You pin it for either R series PP or W series PP.

The one pictured is for the W series only, but dual purpose one just has more bolt holes.

 

[Lextreme II]

Nice work Rob. This swap is alot more economical then the V160. W/R transmissions are dirt cheap. I have seen R154 goes for around $150 and V160 is about $2,200 used.

 

[zidaro]

Will your next R-series flywheel batch out be billet and a bit heavier (closer to 30lbs)? Or staying cast.
aaron

 

[SuperRunner]

Not sure yet. I will make at least another 5 flywheels that are cast, and after that depending on my supplier, I will either keep doing the low cost cast, or offer a 35lb billet flywheel, but the cost will probably be close to double.

I might offer both. I might have a pretty good idea by the end of next week.

 

[BARRY]

dual holes is safe?

 

[KazeSupra]

So, what clutch do we use with this flywheel and R154?

 

[SuperRunner]

Whatever is available for the MKIII turbo supra with the R154 would be available to run on this flywheel.

 

[zidaro]

Rob,
I'm thinking for my application I'd really like to run the heavier flywheel. Is this something you will be producing? When do you expect it to be avail. for purchase- including a bellhousing for R151?
Also, are you aware if one of the 4cyl./3.0v6 4x4 toyota clutches mate up to this flywheel?
thanks, aaron

 

[SuperRunner]

I may be offering a heaver billet flywheels. I have not yet worked out the details, and without some financial backing I may not be able to do this unless I had a group buy of 10 or more.

The flywheels I do now I can do in smaller batches, but the billet, I will have to get at a minimum of 20. So even if I had a group buy of 10, I would still have to front quite a bit to pay for the other 10.

Yes, your 3.0 V6 clutches will not. 4cyl will NOT work unless it is a 22RTE.

 

[zidaro]

put me on the list as #1 for a 30+# billet

aaron

 

[Armed_N'_Hammered]

when will you be selling the R154 bell? You can put me on the list for a flywheel too.

 

[zidaro]

35# billet would be beautiful
thanks,
aaron

 

[beario]

are these still available for w58/1uz

 

[SuperRunner]

yes they are

 

[puredrifter]

hey superrunner, i tried PMing you, need a price on a flywheel pls.

 

[scandy001]

superrunner... I need on of these flywheels and soon please! sending PM also

 

[litldv8]

flywheel

i NEED one too please

 

[tom steele]

you still making these?