ecu

Hello to all Who may be, tell me where you can buy a Supercharger kit with Manifold for 3UZ-FE under the Eaton M112. Just need a Strocker Kit: Rotating Assembly, Forged Pistons / H Beam Rods Combo. I only found locked topics, but they did not give any benefit. thank you:)

I am looking at going with the map ecu 3. I am building a high comp engine with good exhaust cams and itb. Was wondering if anyone had any experience with the map ecu on early 1uz. Also my car is manual gearbox.

Im debating on what kind of engine management to run. I will be running 7 psi on my engine. I am curious to hear some success stories. What engine management have you used and had good luck with.

Hello! I'm from Russia, so I write through a translator. Please help me find the pinout ECU 89661-50170 (34p 22p 16p 28p). Thanks in advance!

soo....I got a job delivering pizza (right when gas goes up...) :mad:...and I get the CEL on. Well its cylinder #3....figured it was a easy fix...hahahahaha In the end its the head gasket...(geting coolent on the spark plug) but here are the questions, if you guys would help a 18 year old out...

hey, Im working on a 1uz swap and Im trying to make the engine work without any ECU or digital programming. I have run into a problem with the igniters that send power to the ignition coil assemblies(at least im pretty sure thats what they do.) the igniters are fired in time by a...

While getting together needed components for my build, I was looking for a good high-performance ECU. I eventually set my heart on a Wolf V500. After sending out inquiries to the 5 listed distributors for North America, I only got a reply back from 3, one told me to look else where. Bob of...

1UZFE VVTi engine/trans harness/loom factory ECU, 5 speed Auto MAF etc Basically I can supply complete front cut without the engine (or I guess I could sell with it and I will get another one?) including all the body looms and anything else you might want or need as I have kept it all. I have...

I have an UZZ3x Soarer Engine Control/Transmission ECU for sale. Price: $160 Location: Gold Coast, Qld Australia Works perfectly :) Fits '91 to '94/01 V8s Part Number 89661-24220

Hey fellas, I've been on the forum for a while but haven't really posted that much. I just recently completed my swap, putting a 1UZ from a 97' SC400 into my '98 4Runner. I had Doc over at Phoenix Tuning do the harness conversion for me. Well, the big problem I'm facing right now is not...

Hi, I am planning on using an aftermarket ECU with my 1UZFE (LS400) Powerplant. At the same time will be doing a conversion to Manual to get wrid of the automatic gearbox, hence the reason for not using the OEM ECU. Locally in my country there are a number of ECUs available. Ranging from...

Im just doing some research before i go out and buy a 1uz halfcut and bolt it into my hilux, ive previously managed to get through wiring my old engine which took me a while but have the knowhow now so im after some advice from the people who have been there done that. i have a haltech e6x...

THOR Racing is able to supply, fit and tune Link XLEM ECUs to run the 1/2/3UZ-FE. (fit and tune over in the UK of course) We can also get versions which can run the VVTi and the E-Throttle on the 4.3 3UZ-FE versions and more modern engines. Here is the spec of the ECU. {broken link removed}...

Wondering if anyone can help me out. Trying to either find pinouts for 40/40/40 pin factory ECU (from celsior/crown?) or if some one can tell me which are the 'batt' , '12+' & fuel pump trigger wires on the 3rd plug that would normally go into the car loom. Unfortunately I dont have this plug so...

I have found a replacement ECU with part number 89661-30500 i believe this is from a Crown Majesta can anyone confirm this for me, if it is am i correct that it usually has a separate computer for the Auto, and so could use it with my manual box . my current soarer has the Auto management built...

Hey guys, do you think its possible to interface a Knock Link to the original knock sensors on the 1uz