>>
REGISTER NOW<<
TO REMOVE ADS FOREVER
Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
New profile posts
Latest activity
Menu
Log in
Register
Install the app
Install
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
What's new
New posts
New profile posts
Latest activity
S
Sudsy
replied to the thread
Haltech and A341e
.
All works fine with electronics removed. I think i have found the problem. Will post outcome after i test it today
Yesterday at 7:19 PM
S
Sudsy
replied to the thread
Haltech and A341e
.
Well ECU is all good according to Haltech. The power on grey and red is due to backfeeding through the relay coils on their relay box (...
Thursday at 7:41 PM
K
Kidwithaucf20
replied to the thread
T56 billet bellhousing
.
Can I get a link please?
Thursday at 2:35 PM
P
P Bateman
replied to the thread
Polyurethane Engine Mounts
.
Definitely more vibration (not that the 1UZ is inherently vibey engine). Anything nolathane increases force and vibration transfer...
Thursday at 5:27 AM
J
Johan Oosthuizen
posted the thread
1UZ TO H42 LANDCRUISER
in
General Discussion
.
Anyone more info, perhaps a adaptor drawing, clearance etc.? Any info will help, as I'm soon to fit a 1UZ to my H42 Land cruiser box...
Monday at 7:06 AM
C
C3nturyVette
posted the thread
1GZ-FE in a 79 vette
in
V12 Engines
.
Hey all. Just getting started on planning out my swap. I have both the engine and the car and I'm debating on going n/a with itbs or...
Apr 10, 2024
George_R
reacted to
Zuffen's post
in the thread
ECMs and Earths/Grounds
with
Like
.
The factory uses quite a few engine based ground points. Do it just as the factory has and you shouldn't have any issues. These...
Apr 10, 2024
George_R
replied to the thread
Bmw E36 3uz Swap Problems
.
1) most likely, your ecu was not programed for m/t properly 2) next thing is that, most likely, it is not wired properly at the same time
Apr 10, 2024
S
Sudsy
replied to the thread
1UZFE idle too high.
.
Have you pulled the stepper motor out and cleaned it? Could just be gummed up a bit
Apr 8, 2024
C
chobagz
replied to the thread
1UZFE idle too high.
.
It’s only been 13 years but has anyone figured this out. having trouble with my 96 soarer sometimes starts up at 1.5-2.5k rpm or just...
Apr 7, 2024
K
Klochner
reacted to
Peewee's post
in the thread
Hydraulic FAN
with
Like
.
Yeah, if it like the older 1uz (early 90's) then it uses a seperate ECU for the hydraulic fan. The main ECU has no idea of its...
Apr 6, 2024
P
P Bateman
replied to the thread
Bmw E36 3uz Swap Problems
.
To clarify, your wiring and fuse(s) that connect power to the coils and injectors should be rated to at least 20 amps. If the wiring...
Apr 6, 2024
S
Schraubstock
replied to the thread
Bmw E36 3uz Swap Problems
.
The 20A arrives everywhere at the ignition coils and the injectors. Even if the error occurs
Apr 5, 2024
A
ak47prince
replied to the thread
A341E Auto transmission will not forward when hot .but will move for 200metres after key is turned off for 10seconds
.
Hi Sir, Noted with thanks! I will test your list after I fix the gearbox back to the car . It's very kind of you for sparing some time...
Apr 4, 2024
S
Sudsy
reacted to
P Bateman's post
in the thread
A341E Auto transmission will not forward when hot .but will move for 200metres after key is turned off for 10seconds
with
Like
.
1. Inspect the oil level and top up if required 2. Perform stall test. Warm up the engine, put gear selector in drive, hold down brakes...
Apr 4, 2024
Get alerted about future Lextreme 1UZ, 2UZ and 3UZ product development.
Home
What's new
Top